Showing results: 1081 - 1095 of 1251 items found.
-
INFRASONITUS -
BioAge s.r.l.
The infrasonic signal, acquired by a suitable microphone, is filtered by an active low-pass filter of the fifth order with a cut-off frequency at 20 Hz, with low noise, then it is sampled and acquired by a 16-bit ADC with a speed of 50 samples. / sec. The amplification factor can be set to 0.1 / 0.5 / 1/10.The infrasonic monitoring system includes a complete diagnostic functionality that performs an exhaustive functional test without the use of other tools: this function is extremely useful when the system is installed on the volcano at high altitudes.
-
TestVonics, Inc.
TestVonics power supplies deliver clean, regulated AC power in a 3.5” high bench top or optional rackmount unit. The TVCS-PS-P1350 model has a fixed output of 115V 400Hz Single phase, ideal for testing the TTU-205 Test Sets. The TVCS-PS-1351 model has a variable output with selectable frequency (50/60/400 Hz) and voltage output for testing of a variety of test equipment including the TTU-205 and other air data test sets.
-
P9400C -
Keysight Technologies
The Keysight P9400C solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 18 GHz. The P9400C is particularly well suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch is critical.
-
Pasternack Enterprises, Inc.
Pasternack directional coupler category is passive devices that couple part of the transmission power in a transmission line. Our directional coupler series provides the bandwidth, high directivity and higher power that engineers need for their most demanding application designs. RF directional couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack directional coupler components are RoHS and REACH compliant. RF directional couplers are available with 4.1/9.5, 4.3-10, 7/16 DIN, Type N or SMA connectors. Our directional coupler line has 6dB, 10dB, 15dB, 16dB, 20dB, 30dB or 35dB coupling values. Power ratings of our typical and high power directional couplers range from 25 Watts to 70 Watts. Directional coupler frequency range of this product design is from 1 GHz to 8 GHz. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this directional coupler series is in-stock. Not only are these couplers in directional design in stock, they also will ship the same day as they are purchased.
-
Series ABC -
Kepco, Inc.
Kepco¹s ABC bench power supply embodies the latest features: keyboard data entry, interactive digital display, integral GPIB support, software calibration, high frequency switch mode conversion, wide range input (85-264V a-c) and power factor correction. It meets the EN 61000-3-2 harmonic limits. A built-in EN 55022 Class B input EMI filter is provided. Integral External Trigger and RS 232 ports are now standard features.
-
upj10 -
KEYCOM Corp
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Shanghai Tarluz Telecom Tech Co., LTD
Adopting new techniques like advanced radio frequency and digital hybrid integration design, broadband and fundamental wave mixing, digital IF processing and intelligent power management, etc., The Cable and Antenna Analyzer has advantages of fast measuring speed, high measurement accuracy, small size, light weight, battery power, touch screen operation and adjustable backlighting. It can measure return loss, standing wave ratio (SWR), impedance, phase, DTF (discontinuity point fixing), etc.
-
Verticon® 100 BGA -
Johnstech International Corporation
The Verticon® 100 BGA socket /contactor is an elastomer based contactor technology featuring a combined contact profile, and proprietary plating, and solid contact dynamics providing low inductance and stable contact resistance under multiple (production) landing test conditions. The overall design architecture of the Verticon® 100 contactor enables functional test hardware interface compliance as required by precision analog/mixed signal, high speed digital and RF SOCs’ up to the millimeter wave frequency domain.
-
Extech DM220 -
Extech Instruments Corporation
This Mini Pocket MultiMeter has a large high contrast 4000 count LCD display, Non-Contact Voltage detection for identifying live circuits, and a built-in Flashlight. It measures AC/DC Voltage, AC/DC Current, Resistance, Frequency, Duty Cycle, Diode Test and has a Continuity Beeper. Additional features include: built-in storage clips for integrated test leads, double molded housing to provide extra protection, over-range and low battery indication. Complete with test leads and 2 AAA batteries.
-
J2180A -
PICOTEST Corp.
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
1GG7-8045 -
Keysight Technologies
The 1GG7-8045 is a broadband GaAs MMIC Traveling Wave Amplifier designed for high output power and moderate gain over the full 2 to 26.5 GHz frequency range. Seven MESFET cascode stages provide a flat gain response, making the 1GG7-8045 an ideal wideband power block. Ebeam lithography is used to produce gate lengths of ~0.3 mm. The 1GG7-8045 incorporates advanced MBE technology, TiPtAu gate metallization, silicon nitride passivation, and polyimide for scratch protection.
-
72-7755 CAL D -
Tenma
The 72-7755 CAL D from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
-
72-7755 CAL -
Tenma
The 72-7755 CAL from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
-
72-7755 CAL DU -
Tenma
The 72-7755 CAL DU from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
-
Pasternack Enterprises, Inc.
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
